Abstract
In this paper, Cu-coated graphite powders for a low thermal expansion coefficient and a high thermal conductivity are fabricated using a chemical reaction process. The Cu particles adhere to the irregular graphite powders and they homogeneously disperse in the graphite matrix. Cu-coated graphite powders are coarser at approximately 3~4 ㎛..... More

Abstract
In this study, a glass fiber is fabricated using a continuous spinning process from alkali resistant (AR) glass with 4 wt% zirconia. In order to confirm the melting properties of the marble glass, the raw material is placed into a Pt crucible and melted at 1650 ℃ for 2 h,..... More

Abstract
In this study, a spray drying system was used to prepare macroporous titania micro-particles for applications including UV blocking materials and photocatalysts. To synthesize the macroporous particles a colloidal templating method using polymeric beads as sacrificial templates and a titania nano-colloid as precursor material was adopted. The resulting porous titania..... More

Abstract
In this study, zinc oxide (ZnO) nanostructures were grown on a ZnO-buffered fluorine-doped tin oxide (FTO) substrate using a microwave chemical bath deposition method with different zinc oxide precursor concentrations from 0.01 to 0.5 M. We investigated the effects of the zinc oxide precursor concentration on the morphological, structural, optical..... More

Abstract
The effect of ultrasonic melt treatment (UST) on the microstructure and mechanical properties of Al-7Si-0.35Mg (A356) casting alloys was investigated. The particular aim of this study was to analyze the mechanism involved in the strengthening of the A356 alloys when fabricated by UST. The UST had little effect on the..... More

Abstract
The effects of particle size on the surface properties of HVOF spray coating were studied to improve of the durability of metal components. Micro and nano sized WC-12Co powders were coated on the surface of Inconel718, and the effects of particle size on surface properties were studied. Surface hardness was..... More

Abstract
An AlCrTiSiN film composed of 31Al-15Cr-1.7Ti-0.5Si-51.8N (at%) was deposited on a steel substrate by arc ion plating to a thickness of 1 μm. It consisted of nano crystalline hcp-AlN and fcc-CrN. Its corrosion behavior in Ar-1%SO₂ gas at 800 ℃ for 5-50 h was studied. The resulting scales consisted primarily..... More

Abstract
For the applications in automotive, aircraft, aerospace, and electronic industries, the lightest structural Mg alloys have received much attention since 2000. There has been some progress for the improvement of the mechanical properties such as room temperature strength, formability and mechanical anisotropy. However, the high temperature strength of Mg alloys..... More

Abstract
Sn-doped ZnO (ZTO)/Ag/ZTO tri-layer films were deposited on glass substrates by radio frequency (RF) and direct current (DC) magnetron sputtering and then vacuum annealed at 100, 200 and 300 ℃ for 30 min with a proportions of H₂/N₂ gas flow of 6/6 sccm, to investigate the effects of annealing temperature..... More

Abstract
Computational fluid dynamic modeling of a continuous rheo-casting technology was conducted, consistent with the manufacturing of 3 mm-thin plates made of aluminum alloy A356. The A numerical simulation on of the stabilizing time of the material crystallization was carried out using the ANSYS FLUENT code. Solidification and melting models were..... More

Abstract
In case of the uranium (U) and zirconium (Zr) powders which have been utilized for the production of a metallic fuel in the various nuclear applications, the homogenous distribution of U powders in the Zr-U pellet has influenced significantly on the nuclear fuel performance. The inhomogeneity in a powder process..... More

Abstract
Despite of many attractive properties of TiN, the current concern about the TiN focuses on its low fracture toughness below the ductile-brittle transition temperature. To improve its mechanical properties, the approach generally utilized has been the addition of a second phase to form composites and to make nanostructured materials. In..... More

Abstract
High-purity and good sinterable mullite powder (3Al₂O₃･2SiO₂) was synthesized by a sol-gel process to prepare a high-purity mullite crucible. The densified mullite crucible was fabricated by slip casting with the powder followed by sintering at 1600 ℃. Solar salt was put into the mullite crucible and then fired at the..... More

Abstract
Intermetallic compounds (IMCs) developed on the interface between a solder alloy and its bonding pads are an important factor in the failure of electronic circuits. In this study, the mechanical behaviors of the IMCs formed in the Cu-Ni-Sn ternary alloy system are investigated. Presumably, Ni can act as a diffusion..... More

Abstract
As with any solvent, stabilizing a multivalent element at a given oxidation level in the glass depends on the thermodynamic conditions. The effects of temperature in the oxidation-reduction equilibrium have been previously noted with higher temperatures being conductive to reduced states. 30Ce₂O-70P₂O₅ binary system glasses were prepared. The effects of..... More

Abstract
Despite of the many attractive properties of TiO₂, its low fracture toughness limits many industrial applications. To improve its fracture toughness, the approach commonly utilized has been the addition of a second phase, to form composites, and to make nanostructured composites. In this regard, highly dense nanostructured TiO₂ and TiO₂-graphene..... More

Abstract
The aim of this study is to establish an optimized hot-press sintering condition for aluminum matrix composites (AMCs) by analyzing their sintered microstructure and mechanical properties. The fabricated AMCs in this study consisted of a blend of commercial Ecka Alumix 431 powder, and Al-Si/SiC_p powder manufactured by gas atomizer (Al-Si/SiC_p)...... More

Abstract
Fe-(20, 45 wt%) Gd intermetallics were vacuum arc melted as the mother alloy of a neutron shielding and absorbing material. The structure of the cast Fe-20 wt% Gd intermetallics had primary dendrites with a short width of about 2 μm, which became coarse with increasing Gd content. The final compositions..... More

Abstract
In order to study the effect of microstructural change on the tensile properties of discontinuous precipitated Al-Zn binary alloy, four different Al-Zn alloys(25, 30, 35, 45 wt% Zn) were aged at 160 ℃ for different aging times(0, 5, 15, 30, 60, 120, 360 min) after being solution treated at 400..... More

Material Analysis & Characterization

Abstract
ZnO buffer layers were deposited on mica substrates using a sol-gel spin coating method. Then, a thin film of metallic Zn was deposited onto the ZnO buffer layer/mica substrate using a thermal evaporator, and the deposited Zn thin films were then thermally oxidized in a furnace at 500 ℃ for..... More

Modeling and Simulation

Abstract
Yttrium Aluminum Garnet (YAG) single crystal has received much attention as the high power solid-state laser’s key component in industrial and medical applications. Various growth methods have been proposed, and currently the induction-heating Czochralski (IHCZ) growth method is mainly used to grow YAG single crystal. Due to the intrinsic properties..... More

Plastic Working & Materials Processing

Abstract
Laser surface carburizing can be achieved by a laser alloying mechanism, which includes melting the graphite coated substrate and dissolution of the graphite in the liquid state. The drawback of laser carburizing is that process-induced cracks frequently form on the carburized surface as a result of carbon enrichment and the..... More

Abstract
Fe-TiB₂ powder was synthesized in-situ by the planetary ball milling and subsequent heat-treatment of an iron boride (FeB) and titanium hydride (TiH₂) powder mixture. Mechanical activation of the (FeB+TiH₂) powder mixtures was observed after a milling time of 3 hours at 700 rpm of rotation speed, but activation was not..... More

Abstract
In the present study, we systematically investigated the effect of entropy of mixing (ΔS_mix) on the mechanical and thermal properties of single phase FCC solid solutions with multi-principal elements. An increase in ΔS_mix led to an increase in micro-hardness and a decrease in thermal conductivity (κ) due to severe lattice..... More

Abstract
In this study, we established a correlation between the electrical conductivity and catalytic properties of vanadium borophosphate glass containing Fe₂O₃. Glasses were synthesized in the 78V₂O₅–15P₂O₅–7B₂O₃ ternary-system containing x mol% Fe₂O₃ (x = 1, 5, 7.5, and 10). Electrical conductivity was measured at 45 ℃ for samples heat-treated at 340..... More

Abstract
The aim of this study is to optimize the microstructure and mechanical properties of Ti-39Nb-6Zr (TNZ40) for bio-implant applications. TNZ40 was designed to have a low elastic modulus (~40 GPa) and good biocompatibility. However, the alloy shows relatively low strength compared to other titanium alloys for bio-implant. In the present..... More

Abstract
Open cell Cu foam, which has been widely utilized in various industries because of its high thermal conductivity, lightweight and large surface area, was successfully joined with Cu plate by diffusion bonding. To prevent excessive deformation of the Cu foam during bonding process, the bonding pressure should be lower than..... More

Abstract
The low mechanical properties of SiC limit its wide application despite many attractive properties. To improve the mechanical properties, a second phase has been generally added to make a nanostructured composite. In this respect, graphene was evaluated as the reinforcing agent of SiC. SiC-graphene composites were sintered within 2 min..... More